Santana/Schock Forum
Home Forums Search Boat Show TSBB Roster Chandlery Events Classifieds Resources More Fun About TSBB	Instructions/FAQ | Rules & Etiquette | Clear Cookies View Thread | Post Response | Return to Index | Read Prev Msg | Read Next Msg | What you see on the trunk is the rigit hard putty Posted By: Seth Dabney, 2023-C, Oxford, MS Date: 5/22/08 3:21p.m. Report: outside forum guidelines In Response To: Also, your last picture suprised me. (Gary, Santana 2023A, Milwaukee) that Schock used. That part of the sole had never been cut out when I did the first job. I just left it alone and put some thick epoxy on top. It is rigid, nothing like cured 5200. I did grind down the top of the sole, at least through the glass layer on top and a little into the wood. It was pretty flat when I got done. I didn't worry to much the last time (below) but you should be able to see that I had at least got down to bare wood over the seams. Seth

Messages In This Thread

Santana 2023 WB Tank: fiberglass 101 -- Gary, Santana 2023, Milwaukee -- 5/13/08 10:46p.m.

Filling the port & starboard seams -- Gary, Santana 2023, Milwaukee -- 5/13/08 10:56p.m.

Oops! Wrong pic above, here it is... I hope! -- Gary, Santana 2023, Milwaukee -- 5/13/08 11:08p.m.

Aft Starboard corner, though they all look similar. -- Gary, Santana 2023, Milwaukee -- 5/13/08 11:20p.m.

overview of a bulkhead in progress -- Gary, Santana 2023, Milwaukee -- 5/13/08 11:27p.m.

broken corner of removed sole piece, repaired and sanded -- Gary, Santana 2023, Milwaukee -- 5/13/08 11:34p.m.

Overview of completed bulkhead -- Gary, Santana 2023, Milwaukee -- 5/20/08 11:09p.m.

you're getting good at this, eh? -- Seth Dabney, 2023-C, Oxford, MS -- 5/16/08 5:07a.m.

Only half as good as you, Seth. Thanks for your help. -- Gary, Santana 2023, Milwaukee -- 5/17/08 3:03p.m.

A completed (covered) corner. -- Gary, Santana 2023, Milwaukee -- 5/20/08 11:17p.m.

I am well pleased with my finished seams. -- Gary, Santana 2023, Milwaukee -- 5/20/08 3:15p.m.

You get the prize... -- Tom Cannon, 2023A, Coupeville WA -- 5/20/08 3:50p.m.

I know what you're REALLY saying, Tom! -- Gary, Santana 2023, Milwaukee -- 5/20/08 10:45p.m.

That's pretty much what I did. -- Seth Dabney, 2023-C, Oxford, MS -- 5/20/08 5:24p.m.

OK Seth -- Bob Frak -- 5/20/08 7:45p.m.

only one of two pieces had been put back -- Seth Dabney, 2023-C, Oxford, MS -- 5/21/08 1:18p.m.

Did you use straight 5200 the length of your trunk? -- Gary, Santana 2023, Milwaukee -- 5/21/08 6:08p.m.

To do what? I didn't use any? -- Seth Dabney, 2023-C, Oxford, MS -- 5/21/08 9:21p.m.

Your immediate reply, third pic from the bottom, may answer it. -- Gary, Santana 2023A, Milwaukee -- 5/22/08 7:16a.m.

Gary / itchy -- Bob Frak -- 5/22/08 8:11p.m.

Hey, Bob. Well, easy to 'jump' on the epoxy/glass, but -- Gary, Santana 2023A, Milwaukee -- 5/23/08 7:41a.m.

Maybe?? -- Bob Frak -- 5/23/08 11:51a.m.

Also, your last picture suprised me. -- Gary, Santana 2023A, Milwaukee -- 5/22/08 7:20a.m.

 What you see on the trunk is the rigit hard putty   -- Seth Dabney, 2023-C, Oxford, MS -- 5/22/08 3:21p.m.

Ah, understood. -- Gary, Santana 2023A, Milwaukee -- 5/23/08 7:56a.m.

I was told on the main board to epoxy the screws in. -- Todd-2023C-SFBay -- 5/24/08 8:18p.m.

Don't be so sure, Todd. Not as easy as 'they' make it sound. -- Gary, Santana 2023, Milwaukee -- 5/25/08 7:57p.m.

I'm humbled, Seth. Awesome work. Here's a great tool I discovered. -- Gary, Santana 2023, Milwaukee -- 5/20/08 10:42p.m.

Same seam, couple hours later, completed. -- Gary, Santana 2023, Milwaukee -- 5/20/08 11:02p.m.

Framing the Edge-Out -- Gary, Santana 2023, Milwaukee -- 5/17/08 3:15p.m.

Giving you a close up here, because... -- Gary, Santana 2023, Milwaukee -- 5/17/08 3:35p.m.

Nothing of major interest here. -- Gary, Santana 2023, Milwaukee -- 5/17/08 4:09p.m.

Awesome job -- Liv, CS22, Karma 22, Ottawa River -- 5/18/08 5:32a.m.

Liv, don't be offering my services out (unless it's a hot friend of yours) -- Gary, Santana 2023, Milwaukee -- 5/18/08 2:13p.m.

Are you going to glass the underside of the edge outs? -- Seth Dabney, 2023-C, Oxford, MS -- 5/18/08 12:34p.m.

If I understand you, Seth, maybe this will clear it up? -- Gary, Santana 2023, Milwaukee -- 5/18/08 2:26p.m.

Seth, after a little sleep, here's the better answer! -- Gary, Santana 2023A, Milwaukee -- 5/19/08 6:23a.m.

A dry fitting. Just checking things out. -- Gary, Santana 2023, Milwaukee -- 5/20/08 10:53p.m.

 

Post Response
Your Name:
Your E-Mail Address:
Subject:
Message Is your topic political? If so, be sure you're posting in The Political Corner
Click here for help on smiley faces and formatting codes If you'd like to include a link to another page with your message, please provide both the URL address and the title of the page:
Optional Link URL:
Optional Link Title:
If you'd like to include an image (picture) with your message, please provide the URL address of the image file: You may upload a file to our server by clicking here.
Optional Image URL:
Please type these four characters into the field below. Do not enter spaces, just numbers and letters.